Yes it works! PropOne is applied to thousands of vessels every year, all around the world.
Since 2012 PropOne has earned a reputation for outstanding performance, worldwide support/customer service and unbeatable value for money.
Once immersed PropOne will work for a minimum of 1 year. After this point the coating will still be there but it will start to loose its effectiveness continue to work depending on local conditions and vessel usage.
PropOne is a two-coat system consisting of a Primer Coat and a Foul Release Coating (Clear Coat). The Clear Coat is a non-biocidal, super-slick coating which prevents organisms from strongly adhering to the surface of the propeller and all underwater fast-moving metals.
Organisms can be easily dislodged once the boat is placed in drive and there is sufficient water flow through the running gear.
The removal of the fouling organisms is purely a mechanical effect. The Clear Coat does not prevent marine growth by chemically poisoning the environment.
You can buy PropOne from:
For more information on shipping times see our shipping FAQ.
Please see our multilingual brief application guides and technical datasheet below for application instructions:
you can also reach out to one of our PropOne accredited applicators. Accredited applicators are trained and supported by both Greencorp Marine and their local distributors. Should you wish to find an accredited applicator in your local area, please contact us and you will receive a list of applicators in your area.
You can also contact a local boatyard or dealer in your area to apply it for you.
Unlike some competitors’ foul release coatings, you are encouraged to apply PropOne™ yourself if you are familiar with application of similar products. To get the best results out of your PropOne kit we suggest you understand and follow our application guides and technical information.
Our three kit sizes correspond to the following coverage areas:
|Propeller size and number of blades|
|Three or four blades||Four or five blades||Five blades|
|Running gear components to be painted||One propeller||250mL Kit||500mL Kit||500mL Kit|
|Two propellers||250mL Kit||500mL Kit||1 Litre Kit|
|Two propellers, two rudders & two propeller shaft struts||500mL Kit||500mL Kit||1 Litre Kit|
|Two propellers, two rudders, two propeller shaft struts & two trim tabs||500mL Kit||1 Litre Kit||1 Litre Kit|
Check out our PropOne Preparation Products:
The Clear coat of the PropOne system has an ultra-slick surface that marine growth struggles to stick to. PropOne Clear Coat contains no copper, tin or any other toxic substances harmful to marine life and it is designed specifically with a long service life in mind when applied to underwater running gear.
In contrast, antifoul paints release chemically poisonous materials to kill marine growth.
All PropOne kits have a shelf life of 3 years from date of manufacture, with the date of expiry being clearly labelled on your kit.
PropOne can be applied to all underwater metallic surfaces:
You can also use our Underwater Light Coating (ULC) clear coat directly on underwater lights.
PropOne does not need maintenance (as it is self cleaning once the boat gets moving on the water) and will remain intact even if the boat is left out of the water for extended periods of time and hauled out/launched repeatedly.
Once the boat has been hauled out, avoid heavy abrasive cleaning like scraping and high pressure hosing. To remove lingering marine growth all that is needed is light wiping with a non-abrasive cloth and light washing with water.
Make sure that if you are having the bottom of the boat high pressure washed, PropOne coated parts are covered to prevent damage to the clear coat.
Allow for surface preparation, either using PropOne Silicone Remover and Paint Stripper or 80-120 grit mechanical grinder before you start painting as well as proper surface cleaning using our recommended surface preparation cleaner, Prop Wash and solvents.
This will be the majority of the time with the painting process being relatively quick.
We suggest a minimum 12 hours drying time after the final coat for an average air temperature of 20°C (68°F) and minimum 16 hours drying for air temperatures of 10°C (50°F). Lower temperatures or humidity will extend cure time.
Minimum time to immersion at 55% RH:
20°C (68°F): 12 hours
10°C (50°F): 16 hours
Lower temperatures or humidity will extend cure time. Minimum application conditions: 10°C (50°F), 55% RH.
PropOne is indeed suitable and recommended for sterndrives and IPS drives, it works well for this application.
PropOne can be used in fresh or saltwater as it is a foul release, not an anti-foul. PropOne relies on a slick surface and flowing water over this surface, meaning Zebra mussels and other freshwater growth will struggle to stick onto your running gear!
When it is time to renew, the old PropOne clear coat and primer must be removed before re-applying.
For this we have a Silicone Remover and a Paint Stripper available to remove the clear coat and primer coat. However, you may opt to use a mechanical grinder for this also. Once removed, normal application can proceed.
See brief application guide for more information
To prepare fresh metal for PropOne application we recommend:
We always recommend using Prop Wash before acetone to ensure the metals are cleaned with an acid based solution to draw out any contaminants.
Acetone whilst being a good cleaner and helping to dry the metal can often leave contaminants inside the porous metal. That could affect adhesion.
If you do clean with Prop Wash after acetone you will see your rag will turn black and the metals are much brighter.
Apply 2 thin coats of primer, as it is a very thin coating. The Clear Coat is much thicker and you only need to apply 1 generous coat.
The surface is touch dry at the point when a gloved finger is lightly touched against the paint surface and no mark is made in the paint nor is paint transferred to the glove.
In the specific case of PropOne primer, when brushing one coat over another the coat underneath is marked by the brushstroke, it isn’t touch dry.
Touch dry for the primer is the point at which the coating loses its “shine”.
Typically this overcoating window lasts anywhere between 3-10 minutes depending on the temperature.
Instructions for subdividing PropOne Primer tins into four
When coating smaller propellers, many users like to split tins of PropOne primer into smaller units to avoid wastage. Because of the inherent tendency of the dense yellow pigment in PropOne primer to settle on the bottom of the tin, it is important to follow these instructions to ensure the composition of the primer remains constant.
Procedures to subdivide Primer
You now have 60mL of PropOne primer in each tin (4 tins total). These can now be stored unopened up to the expiry date on the original PropOne kit.
Procedures to add Primer Activator
The mixed PropOne Primer is now ready to apply.